--- title: Block Ads, split tunnels and other settings in Floxcore description: What the Floxcore settings for Block Ads, split tunnels, App routing, Domestic DNS, connection sharing and more do, and which ones briefly reconnect you. --- This page explains the settings in Floxcore's **Settings** tab and when to change them. The defaults suit most people. Every setting applies only to the device you change it on: copying your setup to another device does not copy them. AUTOMATIC_TABLE_OF_CONTENTS ## At a glance | Setting | Default | Changing it while connected | | --- | --- | --- | | **Block Ads** | Off | Reconnects briefly | | **Split tunnels** | Your local network only | Applies the next time you connect | | **App routing** (Android) | Off | Reconnects briefly | | **Domestic DNS** | On | Reconnects briefly on a location for China; no effect on others | | **Connection sharing** | Off | Reconnects briefly | | **Connect on device start** (Android) | Off | No effect until the next restart | | **TUN inbound** | Off | Reconnects briefly | | **Language** | Your device's language | No effect | All of these are under **Settings → Connection options**, except **Language**, which is under **Settings → App options**. On Android, **Block Ads** is written **Block ads**. "Reconnects briefly" means Floxcore disconnects and connects again by itself, so your apps lose their connection for a moment. ## Block Ads **Block Ads** stops your device from reaching known advertising domains. It only works while Floxcore is connected. It blocks whole domains, so ads that come from the same domain as the page or video itself can still appear. If an app or site stops working after you turn it on, turn it off again. ## Split tunnels **Split tunnels** lists the addresses that connect directly instead of through the VPX service. - The **Default** entries keep your local network reachable: your router, printer, TV and other devices at home. You can't change or remove them. - To add your own, tap **Add IP/subnet** (**Add IP/subnet or host** on Android, where "host" means a single address) and type an IP address, such as `203.0.113.7`, or a range, such as `203.0.113.0/24`. Then tap **Add**. - Website names such as `example.com` are not accepted: only IP addresses and ranges. - To remove one, tap it and choose **Delete**. **Reset default routes** (**Reset to default** on Android) removes all of yours and keeps the **Default** entries. Changes apply the next time you connect. To apply them now, disconnect and connect again. To leave out a whole app instead, use App routing on Android. ## App routing (Android) **App routing** decides, app by app, whether it uses the VPX service. It is only in the Android app. You can also open it with its icon on the **Locations** tab. 1. Turn on **Enable App routing**. 2. Choose the **Default policy**: **Via VPN** (the default) or **Bypass VPN**. 3. Set apps that should behave differently to **VPN** or **Bypass**. Apps left on **Default** follow the default policy. Use **Search apps** to find one, and **Show system apps** to see background services too. Two common setups: - **Everything through the VPX service except a few apps:** keep **Via VPN** and set those apps to **Bypass**. - **Only a few apps through the VPX service:** choose **Bypass VPN** and set those apps to **VPN**. If no app is set to **VPN**, Floxcore warns that no traffic goes through the VPN. Floxcore itself isn't in the list. Addresses in **Split tunnels** connect directly even for apps set to **VPN**. **Reset to default** clears all your App routing choices. ## Domestic DNS **Domestic DNS** is on by default. It only matters on locations for China, where Chinese websites and apps connect directly: it makes them find their servers in China, so their videos load quickly. Leave it on. See [Floxcore in China](/en/docs/floxcore/china#domestic-dns). ## Connection sharing **Connection sharing** lets other devices on your home network, such as a computer or game console, use this device's connection to the VPX service. Floxcore doesn't create a hotspot: the other device must be on the same Wi-Fi or wired network and set to use a proxy. 1. Open **Connection sharing** and turn on **Share connection**. It only works while this device uses Wi-Fi or a wired network. 2. Connect Floxcore. 3. On the other device, set its proxy to one of the **Server:** addresses Floxcore shows, with the port next to it: **HTTP** port `15005` or **SOCKS5** port `15006`. Use the address of your Wi-Fi or wired network. The status line then says **Connection sharing active**, and **Connection sharing log** lists the connections from other devices. Good to know: - The proxy has no password: anyone on the same network can use it. Only turn it on at home, never on public Wi-Fi. - It doesn't work over mobile data or for devices on this phone's own hotspot. On Apple devices, if your device loses Wi-Fi while sharing, Floxcore turns sharing off and you have to turn it on again. - On Android, if this device's address changes, for example on another Wi-Fi network, disconnect and connect again. - On Android, **Split tunnels** and **App routing** don't apply to shared traffic; **Block Ads** does. ## Connect on device start (Android) **Connect on device start** connects to the location you used last when your Android device starts. Connect once from the app first: until you have, Floxcore shows **VPN permission required** and can't turn it on. To keep the connection on at all times, see [Stay connected on Android](/en/docs/floxcore/android#stay-connected). ## TUN inbound **TUN inbound** is experimental. Leave it off unless our support team asks you to turn it on to test a problem. ## Language **Settings → App options → Language** offers **English**, **Nederlands** (Dutch) and **简体中文** (Simplified Chinese). It changes the app's language straight away. ## Reset all settings **Erase all settings** disconnects and removes your setup, your list of locations, your messages and all the settings on this page, and starts the first-time setup again. Find it under **Settings → Reset** on Apple devices, and under **Settings → Factory reset → Reset to factory default** on Android. It keeps your **Floxcore Device ID** and any copy of your setup in iCloud or Google Drive. You rarely need it: try another location or [updating the list](/en/docs/floxcore/locations#keep-your-locations-up-to-date) first.