This page explains how to set up Floxcore, connect, and get the most from the Locations tab. Apple TV and Android TV work a little differently: see Apple TV and Android TV.
Contents
- Set up Floxcore
- Connect
- Read the location list
- Keep your locations up to date
- Where your traffic goes
Set up Floxcore
The first time you open Floxcore, agree to the terms and privacy notice, then choose how to set it up:
- Setup with QR code: scan the QR code from the setup guide for your device. If you are reading the setup guide on the same phone or tablet, tap the QR code instead: it opens Floxcore and sets it up.
- ⋯ → Setup using Floxcore Setup URL: paste a setup link. It must start with
https://orfloxcore://. Tap Load. - Restore from another phone: copy the setup from a device that already runs Floxcore, by iCloud, Google Drive or Bluetooth. See Set up more devices.
Then choose your sorting on the Preferences screen and tap Done.
The QR code on our website expires if you don't use it within 30 minutes. If Floxcore says Failed to load settings, reload the setup page for a new code and try again. If you chose Skip, the Locations tab shows Setup incomplete: tap Continue Setup.
Later, Settings → Load locations from URL and Settings → Load locations from QR code load a new setup. That replaces the one you had, without asking.
Connect
- On the Locations tab, tap a location. This only selects it: a check mark appears.
- Tap Connect at the bottom of the screen.
- The first time, allow Floxcore to add a VPN configuration (Apple devices) or to set up a VPN connection (Android). Floxcore can't connect until you allow it.
The button then shows Connecting… and then Disconnect. To disconnect, tap Disconnect.
If you didn't select a location, Connect uses the location you used last, or else the first one in the list.
To switch location while connected, tap another location. Floxcore disconnects and connects to the new one straight away.
If Connect is gray, your list of locations is empty or (out-of-date), or Floxcore is still connecting or disconnecting. Update the list first: see below.
The icon at the top left shows your device's own network (Wi-Fi, Cellular, Wired or Not connected), not whether Floxcore is connected. While you are connected, a shield icon appears next to it; tap it to see which location you are connected to.
Read the location list
Each location shows:
- Ping: signal bars and a time in milliseconds. More bars mean a faster response. Ping is measured from your device straight to the location, so it shows how quickly the location answers, not how fast your connection will be. unreachable (Apple) or pending (Android) only means the test didn't get an answer: the location may still work, so try connecting.
- E or L with a bar, for Elite locations and locations with a data limit. The bar shows the data you have used out of your allowance, as we report it. See Unlimited, Limited and Elite data.
To measure all locations again, tap the gauge icon at the top right. To measure one, swipe it to the left and tap Update ping (right-click it on a Mac).
Find a location: type in Search location name or country.
Sort the list: tap the sliders icon (Display Preferences), turn on Sort Locations List, and choose Sort by: Last used, Name or Ping. When sorting is off, locations appear in our order. Floxcore has no automatic "fastest location": sorting by Ping comes closest.
A lower ping doesn't always mean a faster connection. If everything is slow, see Why is my connection slow?
Keep your locations up to date
Floxcore downloads your list of locations again by itself when it is 3 hours old, for example when you open the app or your network changes. While you are connected, it also updates every 12 hours or so.
To update it now, pull down on the list, or open Settings → Update location list and tap Update list. After a successful update, the next one has to wait a minute: the screen shows Wait N seconds.
Last updated at the top of the list shows when the list was downloaded. When it is 2 days old, (out-of-date) appears, and Floxcore won't connect until it can download a new list. If updating fails, Settings → Update location list shows the reason after Failure:. See Troubleshooting.
When we change a location while you are connected to it, Floxcore reconnects for a moment to use the new details. If the location you used is gone, Floxcore connects to another one, from the same country when possible, and shows Location changed.
Where your traffic goes
While Floxcore is connected, your device's traffic goes through the VPX service, with these exceptions:
- Your local network, such as your router, printer or TV, is always reached directly.
- Addresses you add under Split tunnels, and on Android the apps you leave out with App routing.
- On locations for China, Chinese websites and apps connect directly. See Floxcore in China.