This page explains the settings in Floxcore's Settings tab and when to change them. The defaults suit most people. Every setting applies only to the device you change it on: copying your setup to another device does not copy them.
Contents
- At a glance
- Block Ads
- Split tunnels
- App routing (Android)
- Domestic DNS
- Connection sharing
- Connect on device start (Android)
- TUN inbound
- Language
- Reset all settings
At a glance
| Setting | Default | Changing it while connected |
|---|---|---|
| Block Ads | Off | Reconnects briefly |
| Split tunnels | Your local network only | Applies the next time you connect |
| App routing (Android) | Off | Reconnects briefly |
| Domestic DNS | On | Reconnects briefly on a location for China; no effect on others |
| Connection sharing | Off | Reconnects briefly |
| Connect on device start (Android) | Off | No effect until the next restart |
| TUN inbound | Off | Reconnects briefly |
| Language | Your device's language | No effect |
All of these are under Settings → Connection options, except Language, which is under Settings → App options. On Android, Block Ads is written Block ads.
"Reconnects briefly" means Floxcore disconnects and connects again by itself, so your apps lose their connection for a moment.
Block Ads
Block Ads stops your device from reaching known advertising domains. It only works while Floxcore is connected.
It blocks whole domains, so ads that come from the same domain as the page or video itself can still appear. If an app or site stops working after you turn it on, turn it off again.
Split tunnels
Split tunnels lists the addresses that connect directly instead of through the VPX service.
- The Default entries keep your local network reachable: your router, printer, TV and other devices at home. You can't change or remove them.
- To add your own, tap Add IP/subnet (Add IP/subnet or host on Android, where "host" means a single address) and type an IP address, such as
203.0.113.7, or a range, such as203.0.113.0/24. Then tap Add. - Website names such as
example.comare not accepted: only IP addresses and ranges. - To remove one, tap it and choose Delete. Reset default routes (Reset to default on Android) removes all of yours and keeps the Default entries.
Changes apply the next time you connect. To apply them now, disconnect and connect again.
To leave out a whole app instead, use App routing on Android.
App routing (Android)
App routing decides, app by app, whether it uses the VPX service. It is only in the Android app. You can also open it with its icon on the Locations tab.
- Turn on Enable App routing.
- Choose the Default policy: Via VPN (the default) or Bypass VPN.
- Set apps that should behave differently to VPN or Bypass. Apps left on Default follow the default policy. Use Search apps to find one, and Show system apps to see background services too.
Two common setups:
- Everything through the VPX service except a few apps: keep Via VPN and set those apps to Bypass.
- Only a few apps through the VPX service: choose Bypass VPN and set those apps to VPN. If no app is set to VPN, Floxcore warns that no traffic goes through the VPN.
Floxcore itself isn't in the list. Addresses in Split tunnels connect directly even for apps set to VPN. Reset to default clears all your App routing choices.
Domestic DNS
Domestic DNS is on by default. It only matters on locations for China, where Chinese websites and apps connect directly: it makes them find their servers in China, so their videos load quickly. Leave it on. See Floxcore in China.
Connection sharing
Connection sharing lets other devices on your home network, such as a computer or game console, use this device's connection to the VPX service. Floxcore doesn't create a hotspot: the other device must be on the same Wi-Fi or wired network and set to use a proxy.
- Open Connection sharing and turn on Share connection. It only works while this device uses Wi-Fi or a wired network.
- Connect Floxcore.
- On the other device, set its proxy to one of the Server: addresses Floxcore shows, with the port next to it: HTTP port
15005or SOCKS5 port15006. Use the address of your Wi-Fi or wired network.
The status line then says Connection sharing active, and Connection sharing log lists the connections from other devices.
Good to know:
- The proxy has no password: anyone on the same network can use it. Only turn it on at home, never on public Wi-Fi.
- It doesn't work over mobile data or for devices on this phone's own hotspot. On Apple devices, if your device loses Wi-Fi while sharing, Floxcore turns sharing off and you have to turn it on again.
- On Android, if this device's address changes, for example on another Wi-Fi network, disconnect and connect again.
- On Android, Split tunnels and App routing don't apply to shared traffic; Block Ads does.
Connect on device start (Android)
Connect on device start connects to the location you used last when your Android device starts. Connect once from the app first: until you have, Floxcore shows VPN permission required and can't turn it on. To keep the connection on at all times, see Stay connected on Android.
TUN inbound
TUN inbound is experimental. Leave it off unless our support team asks you to turn it on to test a problem.
Language
Settings → App options → Language offers English, Nederlands (Dutch) and 简体中文 (Simplified Chinese). It changes the app's language straight away.
Reset all settings
Erase all settings disconnects and removes your setup, your list of locations, your messages and all the settings on this page, and starts the first-time setup again. Find it under Settings → Reset on Apple devices, and under Settings → Factory reset → Reset to factory default on Android.
It keeps your Floxcore Device ID and any copy of your setup in iCloud or Google Drive. You rarely need it: try another location or updating the list first.